Home > load-cells

load cells

Load cell: is a measured force load quantity converter, which covert the load acting upon them into an analogue or digital electronic signal. This measurement conversion makes use of a spring element which distorts under the influence of the load been measured and this distortion is detected and captured with the aid of a strain gauge.

Load Cells: are electronic weight sensors or transducers which purpose is to convert the weight applied to an electrical signal and transmit it to weight indicator or to the PC.

The load cell strain gauge: is an element , usually in the form of a looped electrical resistor in the shape of a strip, when incorporated into a transducer it is mounted on flexible backing material. When a load force , such a weigh load force, is exerted on the flexible backing material in contact with the load cell strain gauge; the resulting distortion of the backing material creates a proportional change in the electrical resistance of the strain gauge,. With the range of elasticity, the size of the mechanical distortion remains proportional to the applied mechanical force distortion into the load cells, so, the change of the resistance again in the load cell strain gauge is and electronic measurable proportion to the input load cell force quantity applied.

The loading of a load cell: refer  to the mass “m” that acts on the load cell in its measurement direction  (Load E(à 2)), as a dependent weigh load cell force taking into account the local acceleration due to gravity and its related variables.

Load cell types:  The load cell shape and size is determined by the type of the spring element use. The correct selection of the spring element and load cells mounting components depends among on the following factors as, the direction the load force is applied as compression or tension, the maximum load cell force capacity applied, as well  as the service load and the breaking load. The required measurement accuracy  and configuration requirements.

Load cell applications: Special attention must be paid to the load cells application on the points of the load cell; that is to said not only the the points of contact between a load cell and the load cell is intended to weigh, but also those between a load cell and its bearing surface. Load cells sensors should be use in the prescribed direction of loading only. The direction of loading is indicated by an arrow in many load cells. Lateral forces and bending torsional moments must be avoided as far as possible.

 

 

hardware and accessories
hardware and accessories
weighing_assemblies
weighing_assemblies
"s" type
"s" type
shear_beam
shear_beam
single_point
single_point
single ended beam
single ended beam
load compression
load compression
double ended beam
double ended beam
tension link
tension link
fluid damped
fluid damped
miniature cell
miniature cell

Products

alloy steel double ended beam load cell sentronik 7163A 25K lb - 125K lb

Sentronik 7163A Double-Ended Beam Alloy Steel load cell is designed to be center-mounted with doublelinked loading. This design provides free movement in all horizontal directions virtually eliminating binding or friction points. The Shear Beam design gives excellent performance for high capacity loading. This load cell is constructed of alloy steel and fully potted sealed with special chemical compounds to IP67 providing excellent protection against moisture and humidity


Our Price: US$708.00
SkypeAsk a question about this product
alloy steel double ended beam load cell sentronik 7168 25t

Sentronik 7168 Alloy Steel Double Ended Beam load cell is designed for rigid mount and very rugged applications. This makes it an ideal sensor for onboard weighing and any other situation where dynamic loads may be applied. It is available in nickel plated alloy steel. Be assured of consistent, reliable and accurate results while using this loadcell.

Interchangeable with

  • Mass Load ML1100

Our Price: US$890.00
SkypeAsk a question about this product
alloy steel double-ended beam load cell sentronik 7162 50K lb

Sentronik 7162 Alloy Steel Double-Ended Beam Load Cell

3mv/v, 0.03% nonlinearity, 700/700 ohms, 50 ft 4 cond cable, environmentally protected

NTEP 03-079 M IIIL 10,000 div


Our Price: US$796.00
SkypeAsk a question about this product
alloy steel double-ended beam load cell sentronik 7164 5K lb - 200K lb

Sentronik 7164 Alloy Steel Double-Ended Beam load cell is a mid to high capacity nickel-plated alloy steel, double-ended shear beam load cell. This product is designed for use in industrial and outdoor environments. Nickel plated steel construction limits corrosion from outdoor use. The IP67 sealing makes it suitable for applications that are subject to high-pressure wash down. Tank weighing is made simple when this load cell is combined with the EZ mount mounting hardware it was designed for. Its high accuracy and availability in high capacities make it ideal for certified truck and rail scales.


Our Price: US$554.00
SkypeAsk a question about this product
 
Scale market and balances Large warehouse inventory of load cells: From laboratory balances up to truck and hopper electronic digital scales.
Lakefront Business Center 7825 NW 29 Street #137 Miami, FL 33122 U.S.A.
Miami
Florida
U.S.A.
1-877-722-5308